Straight answers to the questions homeowners ask before they buy a kit. For pricing, start with the Price Calculator — or send a photo of your home for a free exact estimate.
How much does it cost to have Govee lights professionally installed?
Installation is priced by your roofline — the footage, the number of stories, and the layout decide it, so there is no honest flat number without seeing the house. Use the Price Calculator on this site for an instant ballpark, or send us a photo of your home and your ZIP code for a free exact estimate. You buy the Govee kit; we install it.
Do you install a Govee kit I already bought?
Yes — that is our main offer. Buy your kit at Costco, Amazon, or Govee.com (or ask us which kit to buy before you order), and we handle the measuring, mounting, wiring, and app connection. Send us the model name and kit length with your estimate request so we can plan the layout.
Which Govee model should I buy — Pro, 2 Pro, Prism, or Elite?
For most homes we recommend the 2 Pro or the Prism: both can be cut to fit your roofline exactly, both are rated for Chicago winters, and they give the best light effects. The original Pro is the proven workhorse and the other cuttable option. The Elite is the Costco model — a good light for simple rooflines — but it cannot be cut and its white is warm only, so the run has to fit its fixed sections.
Can Govee permanent lights be cut to fit my roofline?
It depends on the model. The Pro, 2 Pro, and Prism are designed to be cut and spliced, so the run ends exactly where your roofline ends. The Elite (sold as Permanent Outdoor Lights 2) cannot be cut — cutting it voids the warranty — so an Elite install is planned around its fixed 16.4 ft sections.
Will the 3M tape hold the lights, or do I need screws?
Tape alone is the number one reason these lights come down — heat, cold, and moisture break the bond over time. We mount every light three ways: the factory 3M tape, a bracket over the light, and two screws holding that bracket. That mechanical mount is what makes the installation permanent, and it is covered by our 1-year installation warranty.
How many feet of lights does my house need?
We measure every eave and rake you want lit, zone by zone — front, sides, and back — then add at least 10% for cuts and corners before picking kit boxes, so you never come up short mid-install. You do not need to climb anything: we measure from your photos and satellite imagery for the free estimate. Homes that need more than one controller’s maximum run simply use a second controller, synced with the first in the Govee app.
Where does the power supply go? Do I need an outdoor outlet?
The control box mounts in a sheltered spot near the start of the run, and our standard installation connects to an existing outdoor outlet (a covered GFCI outlet is what Govee specifies). One exception to plan for: the original Pro’s power adapter is rated for indoor use only, so Pro installs are planned around a garage or covered start point. If you want the power supply hidden inside the garage, an indoor power hookup is available as an add-on. Adding a brand-new outlet is an electrician’s job, separate from the light install.
What happens if one light stops working?
The strand works as a chain. The lights before the failed one keep working, and everything after it goes dark until the bad light is replaced — that is also how the fault is found: the first dark light is the one to swap. It does not mean buying a whole new kit, and we can diagnose and replace a failed section.
How do the lights get from the first floor to the second floor, or across a gap?
With a blank extension cord — a cable with no lights on it — that is included in the kit. We route it behind a downspout or gutter so the jump is nearly invisible, and the lit strand never runs across open siding or shingles. The same method bridges a porch, a garage offset, or a step in the roofline.
Can lights be mounted on a gable peak, or where there is no soffit?
Yes. On gable slopes and rakes there is no flat soffit edge to mount to, so we use offset brackets that hold each light out from the surface at the right angle — we stock them in 1 in and 3.5 in offsets for every model family. Fascia and no-soffit mounts are also available, so open eaves do not rule out permanent lights.
How are the wires hidden?
Three ways, depending on the run: the strand sits tight under the eave where it is barely visible from the street, jump cables are tucked behind downspouts and gutters, and a plastic cable channel (cable box) covers the wire where it would otherwise show. The goal is a roofline that looks clean in daylight, not just at night.
Will Govee lights survive a Chicago winter?
The 2 Pro and the Prism are rated down to −22°F, which is why we recommend them here. The original Pro is rated to −4°F. In practice, what kills these systems in winter is rarely the LED itself — it is tape-only mounting letting go and power supplies getting wet, which is exactly what our bracket mounting and sheltered power placement prevent.
How long does a Govee installation take?
Most homes are finished in one day. Larger all-around installs and complex rooflines with many peaks can run longer, and we confirm the timing with your estimate before any work begins.
What warranty do I get?
Two separate warranties, and it is worth keeping them apart. The lights themselves carry Govee’s product warranty — currently 3 years on the permanent outdoor lines — and claims go through the seller, which is one more reason you buy the kit in your own name. Our installation work carries the ESHEN 1-year installation warranty: if our mounting or wiring fails, we come back and fix it.